Perfectionists building tooling
for
Perfectionists

EROWA Store
To Order Call: 1- 586-755-5820

Ordering Code: E1

Click here for warranty

Name : Long Slotted holder for Erowa ITS
Manufacturer : High Quality Sunspot Generic
Condition :   NEW   
Description : 2” wide x 1.25” thick x 5” long aluminum block plus centering plates and posts. 20.5mm slot which is .50” deep. Use for milling large or long electrodes. Superior quality.

The two outside holes are for clearance of the outside locators on 100mm chucks.

Price: $34
 each 

(see our “Discount schedule”)

Ordering Code: E2-20.5

Click here for warranty

Name : ITS “50” Compatible Slotted Holder
Manufacturer : High Quality Sunspot Generic
Part number : E2-20.5
Condition :    NEW    
Description : 51mm x 51mm square aluminum Holder with 20.5mm slot, now 12.5mm deep. Posts are lapped to remove any rock.

Price : $28
 each

(see our “Discount schedule”)

Ordering Code: E2-26.5

Click here for warranty

Name : ITS “50” Compatible Slotted Holder
Manufacturer : High Quality Sunspot Generic
Part number : E2-26.5
Condition :    NEW    
Description : 51mm x 51mm square aluminum Holder with a 26.5mm wide slot, now 12.5mm deep. The solid wall of the holder is .50” from center which is ideal for 1” electrodes. Posts are lapped to remove any rock.

Price : $28
 each 

(see our “Discount schedule”)

Ordering Code: E3-16

Click here for warranty

Name : ITS “50” Compatible Pocket Holder
Manufacturer : High Quality Sunspot Generic
Condition :   NEW   
Description : 51mm x 51mm square aluminum Holder with 16mm pocket. The solid wall is 8mm from center with .5mm clearance on the side with the screws. The pocket is 12.5mm deep.

Price : $28
 each 

 

(see our “Discount schedule”)

Ordering Code: E3-20.5

Click here for warranty

Name : ITS “50” Compatible Pocket Holder
Manufacturer : High Quality Sunspot Generic
Condition :   NEW   
Description : 51mm x 51mm square aluminum Holder with a 20.5mm pocket. The solid wall is 10mm from center with .5mm clearance on the side with the screws. The pocket is 12.75mm deep.


Price : $28
 each 

 

(see our “Discount schedule”)

Ordering Code: E3-26.5

Click here for warranty

Name : ITS “50” Compatible Pocket Holder
Manufacturer : High Quality Sunspot Generic
Condition :   NEW   
Description : 51mm x 51mm square aluminum Holder with a 26.5mm pocket. The solid wall is about .50” from center with .5mm clearance on the side with the screws. This is ideal for 1.00” square blanks. The pocket is 12.75mm deep.

Price : $28  each

 

(see our “Discount schedule”)

Ordering Code: E4

Click here for warranty

Name : ITS “50” Compatible holder
Manufacturer : High Quality Sunspot Generic
Condition :  NEW
Description : 51mm x 51mm square solid blank, 30mm thick aluminum block plus the centering plates and posts.

Price : $25
 

(see our “Discount schedule”)

Ordering Code: E4-B

Click here for warranty

Name : ITS “50” Compatible holder
Manufacturer : High Quality Sunspot Generic
Condition :  NEW
Description : 51mm x 51mm square solid blank, 30mm thick brass block plus the centering plates and posts. Any rocking is removed.

Price : $32 (sold out until approx Oct 15, 2017).

(see our “Discount schedule”)

Ordering Code: E4-T9

Click here for warranty

Name : Storage Tray
Manufacturer : High Quality Sunspot Generic
Condition :  NEW  
Description : Holds 9 Erowa or 54mm Macro holders.

.92” x 13” x 14”

Price :
$9.75

(see our “Discount schedule”)

Ordering Code: E4-ITS

Click here for warranty

Name : Storage Tray – 4 tools
Manufacturer : High Quality Sunspot Generic
Condition :   NEW 
Description : For erowa its 50 holders. Store 4 tools per tray. Trays have interlocking feature.

Price : $3.25 each

(see our “Discount schedule”)

Ordering Code: E4-80

Click here for warranty

Name : ITS “50” Compatible holder
Manufacturer : High Quality Sunspot Generic
Condition :  NEW  
Description : 51mm x 51mm square solid blank, 80mm high aluminum block plus the centering plates and posts.

Price : $24.50 each, buy the quantity that you need
 

(see our “Discount schedule”)

Ordering Code: E5

Click here for warranty

Name : Chucking Spigot
Manufacturer : Sunspot Tooling Systems
Condition :  NEW  
Description : Includes a carbon steel M10 x 1.5, 45mm long bolt.

Price: $23.50  Inventory Reduction Sale - Now: $19 each

Add $1.00 for a Stainless bolt without a flushing hole.
Add $1.50 for a flushing hole in the carbon steel bolt

(see our “Discount schedule”)

Ordering Code: E5-C

Click here for warranty

Name : Compact Chucking Spigot
Manufacturer : Sunspot Tooling Systems
Condition :  NEW  
Description : Includes a carbon steel bolt. Similar to ER-029098. Bolt does not have a flushing hole.

Price : $21 each
Temporarily sold out

(see our “Discount schedule”)

Ordering Code: E6

Click here for warranty

Name : Q-Chuck 50
Manufacturer : High Quality Sunspot Generic
Condition :   NEW 
Description : Handle included. Similar to Erowa E-034387

We grind top and bottom and all 4 sides (concentric with the teeth) within .0001”.

Price : $
835  each

See E13 for multi station milling chucks

(see our “Discount schedule”)

Ordering Code: E6-90

Click here for warranty

Name : Q-Chuck 50, 90 degrees
Manufacturer : High Quality Sunspot Generic
Condition :   NEW   
Description : Handle included for locking the holder in the chuck.

Price :
$875 each

(see our “Discount schedule”)

Ordering Code: E6-90L

Click here for warranty

Name : Q-Chuck 50, 90 degrees
Manufacturer : High Quality Sunspot Generic
Condition :   NEW   
Description : Handle included for locking the holder in the chuck.

SOLD

Ordering Code: E7

Click here for warranty

Name : Chuck for ITS 50 and 100
Manufacturer : High Quality Sunspot Generic
Condition :   NEW   
Description : The base is approx 1” x 4 ¼” x 6” with the overall height just under 2.50” (the handle is included)

Price: $1275 
 

(see our “Discount schedule”)

Ordering Code: E7T

Click here for warranty

Name : Chuck for ITS 50 and 100 Holders
Manufacturer : High Quality Sunspot Generic
Condition :   NEW   
Description : Top Only (bar is included)

Price: $925
 

(see our “Discount schedule”)

Ordering Code: E8

Click here for warranty

Name : Collet Chuck for ITS 50
Manufacturer : High Quality Sunspot Generic
Condition :   NEW   
Description : Accepts ER32 collets and includes the spigot and spanner wrench.
Flushing option: inside is opened to allow larger and longer electrodes plus you receive a set of 10 seals with wave washer.

Price: $475 without flushing.

Price: $685 with flushing.

(see our “Discount schedule”)

Ordering Code: E9

Click here for warranty

Name : Starter Package for erowa 50mm ITS system
Manufacturer : High Quality Sunspot Generic
Condition :   NEW   
Description : 2 Q-Chucks, 5 spigots and 10 holders of your choice. Holders: 20.5mm and 26.5mm slotted or pocket. You can mix and match if you wish, or we can make a custom package for you at a savings over and above our normal percentage discount.

Price : $1995
 

(see our “Discount schedule”)

Ordering Code: E10

Click here for warranty

Name : 20mm to erowa ITS adapter
Manufacturer : Sunspot Tooling Systems
Condition :   NEW 
Description : Handle for locking erowa ITS holders is included. Internal flushing is provided. Concentricity is not guaranteed but the tool is square, 20mm to the Q-chuck.

Price : $1175
 

(see our “Discount schedule”)

Ordering Code: E11

Click here for warranty

Name : Locking Ring for Spigot
Manufacturer : Sunspot Tooling Systems
Condition :   NEW 
Description : Replace your worn locking rings for greater accuracy.
Stainless Steel for corrosion resistance.

Price : $6.50  each 

(see our “Discount schedule”)

Ordering Code: E12

Click here for warranty

Name : Checking Pin
Manufacturer : Sunspot Tooling Systems
Part number :
Similar to ER-010723
Condition :   NEW 
Description: Excellent tool for squaring your chuck on the ram of your edm machine which dramatically increases accuracy

Price : $875  each

(see our “Discount schedule”)

Ordering Code: E13

Click here for warranty

Name : 3 or 4 station milling chuck
Manufacturer : Sunspot Tooling Systems
Condition :   NEW   
Part number : E13-3 or E13-4
Description : 3 or 4 Generic chucks. The base is .75” thick by 3” wide. Center to center of the chucks is 4”. Overall length is 13” for the 3 station and 17.2” for the 4 station. This tool can be bolted directly to your table or on the optional stand offs which makes it easier to clamp the holders.

Price for 3 station: $3725

Price for 4 station: $4825

Price for standoffs: $30 each

(see our “Discount schedule”)

Ordering Code: E14

Click here for warranty

Name : Extension for Erowa ITS System
Manufacturer : Sunspot Tooling Systems
Condition :   NEW   

Description : Extension for burning down in deep pockets and can eliminate having to build up your work piece to a higher level. Includes Chuck, spigot and lever.

SOLD

Ordering Code: E15

Click here for warranty

Name : Extension for Erowa ITS System
Manufacturer : Generic
Condition :   NEW     
Description : High quality Generic. For burning deep pockets and can eliminate having to build up your work piece to a higher level. Steel. The chuck is square but not perfectly central. The customer can tram the tool to be central. Includes Chuck, spigot and lever.

Overall length is about 5.8” (147mm)

Price : $1090

(see our “Discount schedule”)

Ordering Code: E16

Click here for warranty

Name : Compact Chuck
Manufacturer : Erowa
Part number : ER-020963
Condition :   USED   
Description : Excellent plus condition. Pneumatic!

Price:
$725

1 year warranty

(see our “Discount schedule”)

Ordering Code: E16-D

Click here for warranty

Name : Compact Chuck
Manufacturer : Erowa
Part number : ER-020963
Condition :   USED   
Description : Excellent plus condition. Pneumatic

Price: $1475  Inventory Reduction Sale - Now: $1215 each (2 Chucks mounted to a steel base).

1 year warranty

(see our “Discount schedule”)

Ordering Code: E17

Click here for warranty

Name : Auto Chuck
Manufacturer : Erowa
Part number : ER-007533
Condition :   USED   
Description : Excellent plus condition. Pneumatic. New large o-ring is supplied but not shown.

Price: $790
 (as is, working well, 30 day warranty)

Price: $990  (full disassembly and serviced by Sunspot. 1 year warranty)
 

(see our “Discount schedule”)

Ordering Code: E18

Click here for warranty

Name : Auto Chuck
Manufacturer : Erowa
Part number : ER-
Condition :   USED   
Description : Excellent plus condition. Pneumatic.

Price: $790 (as is, working well, 30 day warranty)

Price: $990 (full disassembly and serviced by Sunspot. 1 year warranty)

(see our “Discount schedule”)

Ordering Code: E23-2

Click here for warranty

Name : Sensor - Probe tip for Erowa
Manufacturer : High Quality Sunspot Generic
Condition :   NEW   
Description : Direct replacement for Erowa Sensor. 7mm diameter at the small end and tapped 4mm. Body is 12mm in diameter. Overall length is 85mm. Carbide ball diameter is 2mm. (some older Erowa probes may require 6mm at the small end instead of 7mm. Add $25 if you require 6mm.

Price : $........ with 2mm carbide ball (Temporarily sold out).

NOTE: You must tram your tool after removing or installing a new or used tip. Our service department can do this within .0001” for a cost of $240 (3 day turn around).

(see our “Discount schedule”)

Ordering Code: E23-3

Click here for warranty

Name : Sensor - Probe tip for Erowa
Manufacturer : High Quality Sunspot Generic
Condition :   NEW   
Description : Direct replacement for Erowa Sensor. 7mm diameter at the small end and tapped 4mm. Body is 12mm in diameter. Overall length is 85mm. Carbide ball diameter is 3mm. (some older Erowa probes may require 6mm at the small end instead of 7mm. Add $25 if you require 6mm.

Price : Available soon

NOTE: You must tram your tool after removing or installing a new or used tip. Our service department can do this within .0001” for a cost of $240 (3 day turn around).

(see our “Discount schedule”)

Ordering Code: E23-3T

Click here for warranty

Name : Sensor - Probe tip
Manufacturer : High Quality Sunspot Generic
Condition :   NEW   
Description : Used on some Macro probes (be sure to double check sizes). 8mm body diameter and threaded 6mm (8mm long). Overall length is 57.5mm. Carbide ball diameter is 3mm. 6mm across the flats.

Price : $125 (in stock as of Aug 9, 2017)

NOTE: You must tram your tool after removing or installing a new or used tip. Our service department can do this within .0001” for a cost of $240 (3 day turn around).

(see our “Discount schedule”)

Ordering Code: E23-4

Click here for warranty

Name : Sensor - Probe tip for Erowa
Manufacturer : High Quality Sunspot Generic
Condition :   NEW   
Description : Direct replacement for Erowa Sensor. 7mm diameter at the small end and tapped 4mm. Body is 12mm in diameter. Overall length is 85mm. Carbide ball diameter is 4mm. (some older Erowa probes may require 6mm at the small end instead of 7mm. Add $25 if you require 6mm.

Price : $....... with 4mm carbide ball (Temporarily sold out).

NOTE: You must tram your tool after removing or installing a new tip. Our service department can do this within .0001” for a cost of $240 (3 day turn around).

(see our “Discount schedule”)

Ordering Code: E23-5

Click here for warranty

Name : Sensor - Probe tip for Erowa
Manufacturer : High Quality Sunspot Generic
Condition :   NEW   
Description : 6 or 7mm diameter at the small end (be sure to check this. Most are 7mm) and tapped 4mm. Body is 12mm in diameter. Overall length is 85 - 88mm. Stainless Steel ball diameter is 5mm. (be sure to check sizes carefully before ordering).

Price : $165 with 5mm Stainless Steel ball (in stock as of August 8, 2017).

NOTE: You must tram your tool after removing or installing a new tip. Our service department can do this within .0001” for a cost of $240 (3 day turn around).

(see our “Discount schedule”)

Ordering Code: E23-5S

Click here for warranty

Name : Sensor - Probe tip for Erowa
Manufacturer : High Quality Sunspot Generic
Condition :   NEW   
Description : 6mm diameter at the small end (be sure to check this. Most are 7mm) and tapped 4mm. Body is 10mm in diameter. Overall length is 57mm. Stainless Steel ball diameter is 5mm.

Price : $115 with 5mm Stainless Steel ball (2 in stock as of August 8, 2017).

NOTE: You must tram your tool after removing or installing a new tip. Our service department can do this within .0001” for a cost of $240 (3 day turn around).

(see our “Discount schedule”)

Ordering Code: E23-6

Click here for warranty

Name : Sensor - Probe tip for Erowa
Manufacturer : High Quality Sunspot Generic
Condition :   NEW   
Description : Direct replacement for Erowa Sensor. 7mm diameter at the small end and tapped 4mm. Body is 12mm in diameter. Overall length is 86mm. Stainless steel ball diameter is 6mm. (some older Erowa probes may require 6mm at the small end instead of 7mm. Add $25 if you require 6mm.

Price : $145 with 6mm stainless steel ball. (one in stock as of Aug 9, 2017)

NOTE: You must tram your tool after removing or installing a new tip. Our service department can do this within .0001” for a cost of $240 (3 day turn around).

(see our “Discount schedule”)

Ordering Code: E34

Click here for warranty

Name : 50mm Centering Plate set
Manufacturer : High Quality Sunspot Generic
Condition :   NEW 
Description : Satisfaction Guaranteed

Price: $9.50  Inventory Reduction Sale - Now: $8 each set  

(see our “Discount schedule”)

Ordering Code: E35

Click here for warranty

Name : 100mm Centering Plates
Manufacturer : High Quality Sunspot Generic
Part number : 
Similar to ER-011599
Condition :   NEW 
Description : Measures 90mm across the flats. Stainless steel.

Price :  $26  per set as per image 

(see our “Discount schedule”)

Ordering Code: E36

Click here for warranty

Name : 100mm Centering Plates
Manufacturer : Erowa
Part number : 
ER-011599
Condition :   NEW 
Description : No screws or posts provided. Only the centering plate and underside supports. Only 2 sets available

Price :  $20 per set
 

(see our “Discount schedule”)

Ordering Code: E38

Click here for warranty

Name : Centering Plate set
Manufacturer : High Quality Sunspot Generic
Part number : Similar to ER-036658
Condition :   NEW   
Description : includes 4 feet with M8 threaded studs

Price: $42  Inventory Reduction Sale - Now: $32 per set  

(see our “Discount schedule”)

Ordering Code: E45

Click here for warranty

Name : 115mm diameter Pallet for ITS erowa
Manufacturer : High Quality Sunspot Generic
Condition :   NEW   
Description : Used with Erowa ITS 100mm chuck. 40mm overall height, 37mm center to center for the 4 M10 tapped holes that will accept M8 shcs. Includes a generic spigot with flushing

Price: $225  Inventory Reduction Sale - Now: $175 each

(see our “Discount schedule”)

Ordering Code: E47

Click here for warranty

Name : 148mm diameter Pallet for erowa ITS 100 and 156 (aluminum)
Manufacturer : High Quality Sunspot Generic
Condition :   NEW    
Description : Used with Erowa ITS 100mm chuck. 29mm height of aluminum. 40mm overall height. Various mounting holes. Includes our E35 centering plates installed as shown and one spigot (not shown). Add $15 for E38 centering plates instead of the E35.

These holders works on a 100mm and 156mm Erowa Chuck and is ready for the gripper of an Erowa Robotic Loader.

Price: $385  Inventory Reduction Sale - Now: $315 each, 3 or more $345 Now: $290 each

(see our “Discount schedule”)

Ordering Code: E50

Click here for warranty

Name : P- Chuck for erowa ITS
Manufacturer : High Quality Sunspot Generic
Condition :   NEW     
Description : Pneumatic, 156mm diameter, 33mm height (bottom to the post contact surface). The base is approx .70” x 6” x 9”. Air switch included. 1 year warranty

Price: $2150  Inventory Reduction Sale - Now: $1875

(see our “Discount schedule”)

Ordering Code: E50-T

Click here for warranty

Name : P- Chuck for erowa ITS
Manufacturer : High Quality Sunspot Generic
Condition :   NEW     
Description : Pneumatic, 156mm diameter, 33mm height (bottom to the post contact surface), 1 year warranty

Price:
$1975  each

(see our “Discount schedule”)

Ordering Code: E52

Click here for warranty

Name : Reference Tables
Manufacturer : System 3R
Part number : 3R-936-xxx
Condition :
  USED  , excellent
Description : Hardened with master 20mm dowel holes and tapped M12. Sizes are approx 1.25” (31mm) x 21.625” (550mm) x 33.50” (850mm) and 1.25” (31mm) x 9.875” (250mm) x 33.50” (850mm)

Price: $875  Inventory Reduction Sale - Now: $790 for the smaller unit and $1275 - Now: $1100 for the larger. FREE shipping is not offered on this particular item.

(see our “Discount schedule”)

Ordering Code: E54

Click here for warranty

Name : Vise, Self Centering
Manufacturer : High Quality Sunspot Generic
Condition : NEW  
Description: Jaws are .75” deep, open to 1.75” and are 2.00” long. 4mm hex wrench and spigot are included.

Price: $775  Inventory Reduction Sale - Now: $690

(see our “Discount schedule”)

Ordering Code: E55

Click here for warranty

Name : Vise, 150mm
Manufacturer : High Quality Sunspot Generic
Condition : NEW  (Stainless Steel)
Description : Very high quality wire edm vise. 150mm (just under 6”) max opening, depth of the jaw is 50mm (1.96”). Overall sizes are: 22mm thick x 148mm x 370mm. The underside plate makes contact with your table and allows the main vise to be adjusted square and parallel.

Price: $1935  Inventory Reduction Sale - Now: $1825

(see our “Discount schedule”)

Ordering Code: E56

 

 

 

Click here for warranty

Name : Vise, 100mm
Manufacturer : High Quality Sunspot Generic
Condition : NEW  (Stainless Steel)
Description : Very high quality wire edm vise. 100mm (3.94”) max opening, depth of the jaw is 14mm. Overall sizes are: 15mm thick x 98mm x 145mm. Similar to 3R-292.3

Maximum weight that can be held is approx 14 pounds.

Price :
$1125

(see our “Discount schedule”)

Ordering Code: E57

Click here for warranty

Name : Vise, 52mm
Manufacturer : High Quality Sunspot Generic
Condition : NEW  (Stainless Steel)
Description : Very high quality wire edm vise. 52mm (2.0”) max opening, depth of the jaw is 25mm. Overall sizes are: 29mm thick x 85mm x 120mm. Center to Center for 8mm mounting screws is 50mm. Includes case.

Price: $445  Inventory Reduction Sale - Now: $325

(see our “Discount schedule”)

Ordering Code: E58

Click here for warranty

Name : Vise, 52mm
Manufacturer : High Quality Sunspot Generic
Condition : NEW  (Stainless Steel)
Description : Very high quality wire edm vise. 52mm (2.0”) max opening, depth of the jaw is 19.5mm. Overall sizes are: 21mm thick x 100mm x 102mm. Center to Center for 8mm mounting screws is 50mm.

Price: $390  Inventory Reduction Sale - Now: $310 without case. Add $25 is you want the case.

(see our “Discount schedule”)

Ordering Code: E59

Click here for warranty

Name : Wire tooling Rule
Manufacturer : System 3R
Part Number: 3R-239-XXX and other
Condition : USED (as new)
Description : Many sizes are available. 1 set measures 406mm to working ends and 438mm overall length. Another set is 36mm thick x 86mm wide x about 594mm overall length.

Price : $? Call for prices and options

(see our “Discount schedule”)

Ordering Code: E62

Click here for warranty

Name : Touch Probe for the Erowa ITS System
Manufacturer : High Quality Sunspot Generic
Condition : NEW

Description : Spring loaded tip. A generic Spigot is included at no cost.

Price : $1250 (with 5mm or 6mm ball)

NOTE: You must tram your tool after removing or installing a new tip. Our service department can do this within .0001” for a cost of $240 (3 day turn around).

(see our “Discount schedule”)

Ordering Code: E65

Click here for warranty

Name : Touch Probe for the Erowa ITS System
Manufacturer : High Quality Sunspot Generic
Condition : NEW

Description : Low cost tool with solid probe tip with 5mm ball. Spigot included.

Price:
Temporarily sold out

Ordering Code: E70

Click here for warranty

Name : Center Finding tool for the Erowa ITS System
Manufacturer : High Quality Sunspot Generic

Condition :  NEW

Description : Excellent for finding the center of a chuck and checking how square the chuck is. Spigot is included.

Price : $625
 each

(see our “Discount schedule”)

Ordering Code: E85

Click here for warranty

Name : Adapter, Macro to Erowa ITS 50 System
Manufacturer : System 3R
Condition : excellent plus USED
Description : Screw included

Price :
$445

(see our “Discount schedule”)

Ordering Code: E90

Click here for warranty

Name : Basic WEDM Chuck
Manufacturer : Erowa
Condition : Used (Stainless Steel, looks new and never used)
Part Number: ER-035715
Description : Actuated by manual lever. One year warranty.

SOLD

Ordering Code: E96

Click here for warranty

Name : Flat Chuck, Pneumatic
Manufacturer : Erowa
Condition : Used (Stainless Steel, looks new and never used)
Part Number: ER-035714
Description : Pneumatic. Hoses are included as seen in the image. One year warranty.

Price: $2690  Inventory Reduction Sale - Now: $2450

(see our “Discount schedule”)

Ordering Code: E100

Click here for warranty

Name : Flat Chuck, Pneumatic
Manufacturer : Erowa
Condition : Used (Stainless Steel, excellent plus)
Part Number: ER-035714
Description : No hoses included. One year warranty.

Price: $2665  Inventory Reduction Sale - Now: $2400

(see our “Discount schedule”)

Ordering Code: E106

Click here for warranty

Name : Erowa 50 ITS Chuck

Pneumatic with blow-off holes at post contact locations

Price: $1475  Inventory Reduction Sale - Now: $1350

(see our “Discount schedule”)

Ordering Code: E110

Click here for warranty

Name : Erowa

Just in! Details soon

Price: $475  Inventory Reduction Sale - Now: $410

(see our “Discount schedule”)

Ordering Code: E120

Click here for warranty

Name : SNT holder
Manufacturer : System 3R
Part number : Unknown
Condition : USED, like  NEW
Description: Flange has bolt pattern for Macro Chuck

Price: $125  Inventory Reduction Sale - Now: $99

(see our “Discount schedule”)

Ordering Code: E130

Click here for warranty

Name : 20mm holder
Manufacturer : System 3R
Part number : Unknown
Condition : USED
Description : Has M6 bolt pattern for Macro Chuck

Price: $125  Inventory Reduction Sale - Now: $99

(see our “Discount schedule”)

Click here to print this page